JavaScript is disabled. Because that a better experience, please allow JavaScript in your browser before proceeding.


You are watching: 2005 jeep grand cherokee radio aux input

*

Once you carry out that, it will certainly reveal 4 Phillips head screws that must be removed. Carry out that and also carefully remove the head unit to reveal the wires. Right here is how it will look indigenous the rear:
*

Step two: v this install, you will be placing the adapter wires (T-harness) right into the 10-pin and also 22-pin connectors. To get there, eliminate the present wires. (There space tabs that need to be pushed in as they room pulled out to remove them) You can do this without removing any kind of wires yet the 10-pin and 22-pin wires, yet if you wish to fully remove the unit, keep in mind that the radio antenna demands to it is in squeezed as it is pulled outward to eliminate it. Step three: before you install the new wiring T-harness in in between the head unit and the present harness, girlfriend will notice that there is a red wire v a fuse associated to it. You deserve to simply ice this cable off as it is for ignition feeling which isn"t necessary for this install. Now, plug in the male finish of the AUX Adapter 10-pin and also 22-pin wires right into the female receiver of the head unit. Then, take the manufacturing facility male 10-pin and 22-pin wires and also plug them right into the mrs receiving end of the AUX adapter wire harness. By default the AAI-CHY calculation plug (3 pen connector) have to be linked to the VES input exploit of the 10 pen T-harness. If the automobile has factory VES or the factory radio is a single disc (REF), usage the Satellite entry of the 10 pin T-harness.Step four: Now, simply find a snug ar for the adapter behind the head unit. This have the right to be tricky, but just make sure it is out of the method of the head unit so it deserve to fit ago in snugly and also that no one of the wires acquire pinched. It may be a an excellent idea to use a zip tie to clean up the wires as lot as possible and place them out of the way.Step five currently you will need to wire up her AUX cord. Plug in the AUX cord with the RCA jacks. Personally, i wired the AUX cord behind mine cup holders through wiring the down previous the climate regulate knobs and also shifter bezel. Then, I merely drilled a feet in the area just behind and above the cup holders in front of the arm rest/ warehouse area and pulled the cord with there. To carry out this, you must remove the trim as presented here:
*

*

Now, if you ONLY have actually satellite radio and also don"t have actually the VES, (Video entertain System) you currently simply have to do the reverse procedure to re-install the trim and also head unit. But, if you have actually the satellite radio and also VES, you must disconnect the VES. To carry out so, i disconnected the power harness presented in the picture below:


See more: How To Convert A 4L60E To Non Electronic, Whats Needed To Install A 700

Removing this cable works, yet throws a trouble code. (It does not revolve on the examine engine irradiate or anything, just a code) To resolve this, you need to remove the other end of the VES wiring which ns did not also bother to execute as it doesn"t stroked nerves me. Now, just re-install the trim and also head unit and you are done!Here space the procedure instructions from the PAC Audio manual:If simulating VES
: Turn the radio on and also press the MODE button to choose DVD or VES. 1. Push the seek up or down switch to choose CHP 1 for Aux 1 or CHP because that Aux 2.Note: as soon as the an essential is removed and the doors continue to be closed, the Radio will screen DVD Paused or strength Off. The Aux source audio will certainly be muted throughout this time. This is a normal function for the manufacturing facility radio. When the vital is turned to Accessory or Ignition, the Aux source audio will un-mute.If simulating Satellite receiver: The radio will should be update with information prior come use. This is one time procedure and will certainly not must be done again uneven the radio is disconnected or automobile battery is replaced/disconnected.Turn the radio on and also press the MODE button to pick Satellite. On solitary disc radios (REF model), wait at least 1 minute prior to using. Navigation (REC) or 6 disc (RAQ or RAK) radios will screen ‘UPDATING CHANNELS’, you re welcome wait till the information disappears.1. Press the look for up or down switch to select Channel 1 because that Aux 1 or Channel 2 because that Aux 2.Note: If you perform not listen the audio source in aux mode, please inspect that the 3 pin connector is linked to the correct connector top top the 10 pen t-harness.I expect this helps! Feel totally free to ask any other questions and all snapshot credit goes to WKJeeps.com thank you! :thumbsup: