There space two defense screws the secure the screen to the frame and they sit on each side the the dock connector. Usage your 5-point protection screwdriver to eliminate them. They space both the exact same size so it\"s okay if you mix them up.

You are watching: Iphone 5s button replacement

3. Eliminate the display display assembly

Place her suction cup slightly above the Home button assembly and also secure it to the screen.
\"*\"
Holding the iphone phone in location with one hand, gently pull upwards ~ above the suction cup till you cost-free the bottom of the screen yet do NOT traction up all the way at this point as a cable to run to the Touch i would sensor is tho connected. You only want to separate the screen around an customs at this point.
\"*\"
Now that you have actually a clear see of the cables, use the pointed edge of your spudger tool in order to very closely remove the metal shield spanning the Touch identifier cable.Make certain you don\"t lose the metal guard that covers the Touch identifier connector.
\"*\"
Again, use the pointed edge of her spudger tool in order to disconnect Touch ID.You deserve to now safely swing the screen up an ext in order to watch where the is connected to the board. Remove the four screws holding under the shield that covers the display cables. To carry out this, use your #000 screwdriver.Once all 4 screws room removed, closely remove the shield and set it aside.
\"*\"
Now use your spudger tool in stimulate to remove the three cables shown in the photo below. You\"ll need to remove the two off come the much right in bespeak to reveal the third and final cable, i m sorry sits listed below them.The screen assembly must now be free from the human body of the phone. Walk ahead and collection everything but the display assembly aside now.
\"*\"

Note: We supplied the suction cup method here yet if you are not able to gain a firm grip v a suction cup girlfriend can closely work your means around the bottom of the phone between the frame and also display assembly v a razor blade until you have the right to gently pry up using the flat finish of your spudger tool instead. Us recommend making use of plastic razor chisels if girlfriend can find them because they won\"t reason damage come the complete of the iPhone\"s frame.

4. Change the Home button flex

Remove the top appropriate screw holding the Touch i would cable in place using your #000 screwdriver. There is a tiny metal guard underneath, make certain you host it in ar so the cable doesn\"t spin or tear underneath it. Likewise make keep in mind of the orientation that this guard together you\"ll must replace it again during re-assembly.
\"*\"
Once you\"ve obtained the peak screw the end and collection that and also the guard aside, you can fold back part of the Touch identifier cable in order to eliminate the two screws hold in the shield that sits above the Home button. Again, use your #000 screwdriver.
\"*\"
\"*\"
You have the right to now remove the metal shield and set it aside.
\"*\"
Lastly, really carefully use your spudger tool to begin prying increase the Home button assembly which is held in through a little bit of adhesive. Be mindful doing this as it\"s easy to tear cables that operation to the Touch i would sensor.
\"*\"
Once you\"ve damaged all the adhesive under the Home button gasket, the whole Home button assembly must lift the end of the display assembly, Touch ID tho attached. If you\"re having concerns removing the gasket, shot heating increase the switch slightly to rest the adhesive.

See more: Reddit Secret Santa Plus ) Exchanges? Super Plus Secret Santa: Secretsanta

\"*\"
\"*\"
Now simply swap the brand-new Home button flex in the old one\"s place. If girlfriend ordered the components I\"ve recommended over from eTech, the home button is currently in place. If you ordered from elsewhere and got just a flex, you\"ll have to transfer the residence button and gasket over to the new flex. Simply be cautious not come tear the gasket while doing this.

5. Replace the screen assembly

Reconnect the three cables displayed in the photo below, beginning with the cable to the far left, which sits underneath the various other two.Replace the display shield using the four screws and your #000 Phillips screwdriver.Re-connect the Touch i would cable come the logic board. The simplest tool to aid you carry out this is the pointed finish of the spudger tool.Replace the Touch identifier shield the sits end the cable.Carefully heat up the top that the display into the height of the frame. Snap under the display screen until the clicks into place.

If the display screen doesn\"t want to go back down, carry out NOT pressure it. Instead, be sure that the height is lined up correctly and also that friend aren\"t snagging any cables. There must be no resistance as soon as snapping it back into place. If there is, you aren\"t lining it increase correctly.