You are watching: Two up 3d printer
See more: Motorola Droid Ultra Vs Droid Maxx (Xt1080M), Compare Motorola Droid Ultra Vs
***Note...While whatever I claimed holds true, the manage board for this press has changed since my post.***Other updates at finish of reviewFirst turn off let me say this is not a plug and also go printer. You"re no going to unpack it and also start printing. This is a kit, and it will certainly take part time to placed together. You will additionally spend a an excellent deal the time dialing in settings and also getting frustrated. In ~ the end of the all, girlfriend will likewise have a an excellent working understanding of just how these things work. I knew the going in, so i was fine through that. If that"s not something you space ok with, then this might not be the kit because that you.If you"re still reading, this is my suffer so far.Packing/Shipping: Nothing bad to say. It shipped a day ahead of time and also arrived two days later in good condition. Some believe this belonging on the providers page, but because this product is only readily available by one supplier, and also they take care of the shipping, i think the is ideal here.Assembly:It was easy enough. Just go step by step, and also take your time. Store in mind that you space screwing right into MDF. Bolts must be snug, however not torqued down. You may likewise want to have actually a knife and sandpaper handy. I found that one of the parts had actually a hole that was almost 3 millimeter off, and also the tab had to be trimmed substantially to obtain it come fit. The remainder were pretty tight, yet manageable.There were some parts not there, and a few others have actually been changed without amending the manual, but all at once it was basic enough.You"ll discover that the instructions call for 6 level washers that space not supplied. Follow to QUBD, these space no longer needed. Possibly I acquired a unique kit, yet they for sure were required as there is a around 2mm gap between the bolt head and what the is holding with each other without them.The component that stop the hot end to the press calls for 2 30mm bolts, however the ones I gained were 25mm. Also, the bolts stop the develop platform space M3 rather of M4 as listed. In both cases the replacements operated fine, however it"s something come be mindful of.Structure:Seems solid enough. Ns wouldn"t to trust it to endure a fall from a desk, but there is very small movement in the solved parts. There"s part sagging and also wobbling in a couple of of the relocating parts together I didn"t use the encourage superglue ~ above them. I would assume that would solve a lot of those issues, but because I setup to customize this printer quite greatly I didn"t bother v it. It"s fully usable as it sits.Printing:I"ve only printed one part so far, and it to be OK. Not great, but far better than supposed for a first go. Getting everything collection up and calibrated is a little of a confusing procedure for the newcomer, but as whole hasn"t been too bad. It"s going come take some tweaking to get really great prints, however looking in ~ the first try over there doesn"t appear to be any reason the shouldn"t it is in possible.Overall Impressions:I went into this learning the job-related that to be going come be connected with getting everything set up and also working. I knew the perfect prints ideal out the the gate were not likely at all, and I was mindful of some of the structural concerns that have been provided here and also elsewhere. As someone wanting to learn exactly how to construct, modify, and troubleshoot a 3D printer, this is a good choice because that me. It might not be because that you.I look in ~ it this way: buying the motors, control board, power supply, and hot end alone can conveniently run girlfriend $200 retail. You"d still need the rods, belts, hardware, and frame. Yeah, girlfriend can find the parts cheaper ~ above ebay, yet for someone new to the understand that wants to build a printer, this is a great place to start.The good thing about 3D printers is the they have the right to print their very own upgrades. I plan to be doing a many that in the coming weeks, and have no doubt that this printer will soon be one even more capable machine.March 05A tiny while ago my Printrboard quit responding altogether. After going through all the actions I might think of to revive the board, I sent out a message to QU-BD v the contact form here so late Wednesday night. Thursday morning I had an email response instructing me to send the old one earlier and they would certainly send a replacement as soon as they had actually tracking info. I mailed it later that day and also sent the info, and also received confirmation and tracking on mine replacement. That left their facility the following day, and also was top top my printer by Monday. I"ve heard a lot of of poor reviews on the customer organization from them, yet I"ve never had an issue. Three organization days from suggest of call to replacement in hand is pretty an excellent if girlfriend ask me.